Soffit and Fascia in Brantford
The roof edge rebuilt properly, with ventilation that works and a fascia line that carries the eavestrough without sagging.
The roofline is where most exterior water problems start, and it is the part of the house nobody looks at until something sags. Brantford Siding Co replaces soffit and fascia across Brantford and Brant County, usually as part of a wider exterior job.
Why it fails
Fascia takes the most direct water exposure of any trim on the house. It sits at the drip line, it carries the weight of a full eavestrough, and on a lot of older homes it was never back-primed on the cut ends. Add three decades of freeze and thaw and the board softens from the back, where nobody can see it, long before the paint gives up.
Soffit fails differently. Older wood soffit was often solid with a few small vents cut into it, which was never enough intake for the attic above. When homeowners later added insulation without baffles, the remaining vents were blocked from the inside. The result is an attic that cannot breathe, which shows up as ice damming at the eave and, in bad cases, moisture staining on the underside of the roof deck.
What we install
Vented aluminum soffit is the usual choice, in a continuous perforated profile that provides intake across the whole eave rather than at a few points. Vinyl soffit is also available and performs well in the right application. For fascia we either cap sound wood with formed aluminum, bent on site to fit the actual board, or replace the fascia entirely where the wood has gone.
Capping is a fabrication job more than a supply one. The aluminum is run through a brake and folded to the exact profile of the roof edge, so the finished line is straight even where the framing behind it is not. That precision is what separates a roofline that looks new from one that looks wrapped.
Doing it in the right order
Soffit, fascia and eavestrough all meet at the same place, so replacing one and leaving the others is how you end up paying for the same access twice. Where a house needs siding as well, the roofline goes first, because the siding tucks up under the finished soffit rather than being cut around it afterwards.
Get a free quote, and see eavestrough installation if the trough is due at the same time.
What's Included
- Vented aluminum and vinyl soffit
- Aluminum-capped or full replacement fascia
- Attic intake ventilation kept clear
- Coordinated with eavestrough in one visit
Other Services We Offer in Brantford
Soffit and Fascia Questions
What is the difference between soffit and fascia?
Soffit is the horizontal underside of the roof overhang, the panel you see when you stand under the eave and look up. Fascia is the vertical board running along the roof edge that the eavestrough fastens to. They meet at a right angle and are almost always replaced together, because reaching one means removing the other.
Why does soffit need to be vented?
Because your attic needs a continuous path for air to enter low and leave high. Soffit vents are the intake side of that system. Block them and the attic gets warm and damp in winter, which drives ice damming at the eave and shortens the life of the roof deck. When we install soffit we keep the intake path clear, including making sure insulation has not been pushed into the vent channel from inside.
Can you just cap the fascia instead of replacing it?
Often yes. Aluminum capping over sound wood fascia is a legitimate approach that costs less and looks the same from the ground. It only works when the wood underneath is solid. Capping over rotten fascia hides the problem and traps the moisture that caused it, which is why we look before we quote.
My eavestrough is pulling away from the house. Is that a fascia problem?
Usually, yes. Eavestrough hangs off the fascia, so when the fascia softens the fasteners lose their grip and the trough starts to sag and pull. Re-hanging the trough on failing fascia buys a season at best. Fixing the fascia is the actual repair.
Get a Free Soffit and Fascia Quote
Tell us about your house and we will come measure it. Free, written, and no pressure afterward.